testpassport 000-232 题库
Certified Administrator 000-232 试题库由资深IT认证讲师和 Certified Administrator产品专家结合 PROMETRIC
或 VUE
的真实考试环境最新原题倾心打造.最新 testpassport000-232 1.Which command lists out the physical volume names as well as total/free PPs in volume groupdatavg?A.lsdev -Cl datavgB.lsvpcfg datavgC.lspv -p datavgD.lsvg -p datavgCorrect:D2.A system administrator needs to configure dump devices for the system. Which commandwould be used to estimate the size required for a dump device?A.lsdevB.chdevC.sysdumpdevD.sysdumpstartCorrect:C3.Which command restarts the TCP/IP subsystem?A.refresh -s inetdB.refresh -s tcpipC.refresh -g /etc/rc.tcpipD.refresh -g /etc/inetd.confCorrect:A4.Prior to implementing an LPAR system, which of the following needs to be done?A.A graphics monitor must be attached to the serverB.Cluster System Management (CSM) software must be installedC.The LPAR system must have an Hardware Management Console (HMC) connectedD.Each LPAR must be configured with a CDROM for operating system installationCorrect:C5.A system administrator's daily monitoring has revealed a failing disk drive. The drive that isfailing, hdisk0, is a lvm mirrored drive. What is the first step that should be taken in order tophysically replace this drive?A.Remove the physical volume from the system.B.Remove the physical volume from the volume group.C.Remove the physical partitions from the volume group.D.Remove the logical volume copies from the failing drive.Correct:D6.How would the system administrator turn on Dynamic Processor Deallocation?A.Use the diag menu to set dynamic deallocation to 'on'B.Use the chdev command to enable the 'cpuguard' attribute of sys0C.Use the cfgmgr command to change the 'monitor' attribute of proc0D.Use the smitty command with the fast path dynamic_processor_deallocation to turn it onCorrect:B7.A system administrator suspects that there were problems with the AIX installation on a pSeriesserver. Which of the following commands can be used, with the appropriate flags, to view the BOSinstallation output files?A.alogB.errptC.lscfgD.installpCorrect:A8.The system administrator wants to use a new jfslog /dev/fs1log with the filesystem /test/fs1 onthe testvg volume group. The following commands were used to create the log and assign it to thefilesystem: mklv -t jfslog -y /dev/fs1log testvg 1 chfs -a log=/dev/fs1log /test/fs1 While trying tomount the /test/fs1 filesystem the administrator received the error "Cannot mount /dev/fs1lv on/test/fs1: A system call received a parameter that is not valid". What step did the administratormiss that most likely caused the error?A.Use the logform command to format /dev/fs1log as a jfslogB.Use the chlv command to change the lv type of /dev/fs1log to jfslogC.Use the chvg command to change the default jfslog of testvg to /dev/fs1logD.Edit the /etc/filesystems file to change the log associated with /test/fs1 to /dev/fs1logCorrect:A9.A support specialist started to apply an APAR on a system by inserting the tape into the tapedrive, and loaded the fix using smitty installp. The following error message is displayed: tape notin backup format Which of he following will resolve this problem?A.Change density setting to 2B.Set tape device to /dev/rmt0C.Set block size to 0 for variableD.Enable compression on tape deviceCorrect:C10.A system administrator has filesystems that should not be mounted during system startup.How can the system administrator prevent the /data filesystem from being mounted duringsubsequent boots?A.mount -no /dataB.chfs -A no /dataC.mount -t nfs /dataD.chfs -a type=nfs /dataCorrect:B有需要的朋友自己下载(PDF格式)
页:
[1]